HyrdoBlend System Specification

Designed with simplicity and practicality in mind.

HydroBlend is available in two different blends depending on water treatment parameters – HW & CW.

The HW is tailored more towards scale prevention and the CW more towards corrosion  anbd silica control.  If not specified, the HW is the default blend. Both blends will handle scale and corrosion, but are designed to lean towards one or the other. Most important when using HydroBlend products is correct sizing & application. If there are any questions concerning the correct unit to use, please contact SFES and customer service will be able to help in any application. Remember, SFES is a custom house manufacturer. HydroBlend systems allow for flexibility and customization to fit almost any application. If needed, SFES will customize your system to special applications.

There are no settings needed, no electricity required, and no guess work in when the cartridges need replacement. When applied correctly, HydroBlend units will consistently feed product over the life of the cartridge. A simple glance at the housing indicates when replacement it needed. All of the systems come in clear or translucent housings. The product will slowly dissolve over time, and cartridge changes take a couple of minutes. Complete units include delivery head, housing, cartridge, mounting bracket, and filter wrench.

Standard Systems

Model – SC-605

Replacement Cartridge – RSC-5 (HW or CW)
Flow Rate Range – 1-4 gpm*
Est. Treatment Capacity – 40,000 gallons
Inlet / Outlet Connections – 3/4” , 1”
Max Pres. – 125 psi / Max Temp. 100°F
Shipping Dimension – 5.25” x 5.25” x 7.5”
Shipping Weight – 4 lbs

The SC-605 is the primarily used in residential applications. A single cartridge will last roughly12 months in an average residence.

Applications: Residential Whole House, RO Pretreatment, POE Convenience Store / Fast Food, Water Heaters
Notes: Use HW cartridge for Scale Control / CW Cartridge for Corrosion Control

Model – SC-610

Replacement Cartridge – RSC-10 (HW or CW)
Flow Rate Range – 4-7 gpm*
Est. Treatment Capacity – 80,000 gallons
Inlet / Outlet Connections – 3/4” , 1”
Max Pres. – 125 psi / Max Temp. 100°F
Shipping Dimension – 5.25” x 5.25” x 12”
Shipping Weight – 4 lbs

The SC-610 is ideal for small commercial and food service applications. It is primarily used in applications where the water flow rate averages 3-7 gpm. Not recommended for residential use since higher flow rates are required in order to use the entire cartridge.

Applications – RO Pretreatment, Water Heaters, POE Convenience Store / Fast Food, Cooling Towers
Notes: Consistent flow rates of 4 gpm or higher needed, otherwise percentage of product may remain unused.

Model – HBW

Replacement Cartridge – RSC-10 (HW or CW)
Flow Rate Range – 2-7 gpm*
Est. Treatment Capacity – 65,000 gallons
Inlet / Outlet Connections – 3/4” , 1”
Max Pres. – 125 psi / Max Temp. 100°F
Shipping Dimension – 5.25” x 5.25” x 12”
Shipping Weight – 4 lbs

The HBW is designed for use in hot water fed equipment, primarily dish machines and booster heaters. The exclusive translucent high-temp housing is rated up to 160°F and 150 psi.

Applications – Commercial Dish Machines, Booster Heaters, or any hot water feed application in flow range.
Notes: ScaleStick® based cartridges can be used in high-temp housing with standard filter heads.

Model – SC-1.0 / 1.5

Repl. Cartridge – RSC 1.5
Min. Flow Rate – 7 gpm / 15 gpm
Est. Treatment Capacity – 500,000 gallons
Inlet / Outlet Connections – 1”, 1.5”
Max Pres. – 80 psi / Max Temp. 100°F
Shipping Dimension – 7.5” x 7.5” x 15.5”
Shipping Weight – 21 lbs

These units are for commercial and industrial applications where high water usage is expected and flow rates average a minimum of 7.5 gpm.

Applications – Light Commercial, water heaters,boilers, cooling towers, laundry, apartments.
Notes: Minimum flow requirements should befollowed, otherwise product overfeeding may occur.